The specifications in this standard make sites, facilities, buildings and elements accessible to and usable by people with such physical disabilities as the inability . 31 Jul LEGALLY BINDING DOCUMENTUnited States of AmericaAll citizens and residents are hereby advised that this is a legally binding document. Trademarks: “ICC,” the International Code Council logo and “Accessible and Usable Buildings and Facilities (ICC/ANSI Al )” are trademarks of the.
|Published (Last):||5 November 2014|
|PDF File Size:||12.92 Mb|
|ePub File Size:||19.2 Mb|
|Price:||Free* [*Free Regsitration Required]|
The rise for any ramp run shall be 30 inches mm maximum.
ICC/ANSI A117.1 – 2003 (Accessible and Usable Buildings and Facilities)
In a Type A or Type B unit, the rear grab bar shall be permitted to 2003 icc ansi a117.1 24 inches mm minimum in length, centered on the water closet, where 2003 space does not permit a grab bar 36 inches mm minimum in length. The function button shall be identified by the International Symbol for Accessibility and tactile indication.
An abbreviation for teletypewriter. Tactile characters shall comply with Section Ramps shall have landings at bot- tom and top of each ramp run. Bathtubs shall deliver water that is degrees 2003 icc ansi a117.1 49 degrees C maxi- mum.
Purchasers of American National Standards may receive current information on all standards by calling or writing the American National Standards Institute.
Plumbing Elements and Facilities General Removable in-tub seats shall be capable of secure ic. A clear floor space 2003 icc ansi a117.1 with Section shall be provided at call controls.
Tac- tile characters shall be 2 inches 51 mm mini- mum in height. Operable parts on towel dis- pensers and 20003 dryers shall comply with Table Truncated domes shall have a center-to-center spacing of 1.
Floor 203 of ramp runs shall comply with Section At least one of 2003 icc ansi a117.1 active leaves of doorways with two leaves shall comply with Sections Changes in level in floor surfaces shall comply with Section Controls shall be located within one of the reach ranges specified in Section Where criteria in this standard differ from those of 2003 icc ansi a117.1 referenced standards, the criteria of this stan- dard shall apply.
No other fixtures or obstructions shall be within the required water closet clearance. If provided, thresholds at doorways shall 2003 icc ansi a117.1 V 2 inch 13 mm maximum in height. An L-shaped continuous grab bar of equivalent dimensions and positioning shall be permitted to serve the function of separate vertical and horizontal grab bars.
ICC/ANSI A – (Accessible and Usable Buildings and Facilities)
Guardrails or other barriers shall be provided where object protru- sion is beyond the limits allowed by Sections The 20033 device shall remain effective for 20 seconds minimum. When pressure is removed from the up or down scan button for more than 2 seconds, the last floor selected shall be registered as a 2003 icc ansi a117.1 call. Car 2003 icc ansi a117.1 keypads shall be in a standard telephone keypad arrange- ment and shall comply with Section A clear floor space com- plying with Section shall be provided in front of the machine.
All dimensions are subject to conventional industry tol- erances. The level of illumination at the car controls, platform, and car threshold and landing sill shall be 5 foot-candles 54 lux mini- mum.
ANSI A117.1 (2003): Accessible and Usable Buildings and Facilities
Ambulatory accessible compartments shall comply with Section Raised islands in crossings shall be a cut-through level with the street or have curb ramps at both sides.
In a Type B unit, where fixtures are located on both sides of the water closet, a swing-up grab bar complying with Sections The down 2003 icc ansi a117.1 button shall sequentially select floors below the current floor.
Where a 2003 icc ansi a117.1 floor space allows a parallel approach to an element and the side reach is unobstructed, the high side reach shall be 48 inches mm maximum and the low side reach shall be 15 inches mm minimum above the floor.
Hall signals, including in-car signals, shall comply with Section Where any obstruction within 1 8 inches mm of the latch side of a doorway projects more than 8 inches mm beyond the face of the door, measured perpendicular to the asi of the 2003 icc ansi a117.1, maneuvering clearances for a forward approach shall be provided.
Tactile characters for elevator car controls shall not be required to comply with Section The angle of the water stream from spouts within 3 inches 2003 icc ansi a117.1 mm of the front of the drinking fountain shall be 30 degrees maximum, and from spouts between 3 inches 76 mm and 5 inches mm from the front of the drinking fountain shall be 15 ivc maximum, measured horizontally relative to the front face of the drinking fountain.
Characters shall be sans serif.